Natural stone in Azerbaijan: types, uses and price per m²

In Azerbaijan, «kamen» (from the Russian word for stone) is the everyday name for natural stone used for cladding, floors, stairs, facades and memorials. The main types are granite, marble, travertine, local limestone (the sawn «mişar daşı» of Absheron), quartzite, slate and basalt, and they differ sharply in hardness, water absorption and resistance to acid. That is why you choose stone first by where it will go and only then by price. Prices are usually quoted per m² and depend not only on the stone type but also on thickness, surface finish, cutting and installation.
Short answer: as of 22 September 2026, Prayk's Building Materials section has 49 listings with «mərmər» (marble) and 30 with «qranit» (granite) in the title; the lists partly overlap because many sellers offer «marble and granite» in one listing. The median of the 30 priced marble listings is 75 AZN (half at 23–98 AZN), and the 21 priced granite listings also have a median of 75 AZN (half at 20–85 AZN). All marble listings are in Baku; prices are usually per m², but check the unit in each listing.
Types of natural stone: how do they differ?
Three properties decide. Hardness is measured on the Mohs scale (scratch resistance from 1 to 10; glass is about 5.5). Water absorption shows how much moisture the stone takes in — the more it absorbs, the more prone it is to stains and frost damage. Acid reaction tells you whether calcite-based stones will dull from lemon, vinegar and some cleaners.
| Type | Origin | Hardness (Mohs) | Water absorption | Acid | Best for |
|---|---|---|---|---|---|
| Granite | Igneous rock | 6–7 | Very low | Resistant | Floors, stairs, kitchen worktops, facades, yards |
| Marble | Metamorphic (calcite) | 3–4 | Low | Sensitive | Interior walls, bathrooms, window sills, low-traffic floors |
| Travertine | Hot-spring deposit (limestone) | 3–4 | Medium, porous | Sensitive | Facades, terraces, pool surrounds (brushed finish) |
| Limestone, «mişar daşı» | Sedimentary rock | 3 or lower | High | Sensitive | Wall masonry, facades, fences — with water-repellent treatment |
| Quartzite | Metamorphic (sandstone) | 7 | Low | Resistant | Worktops, facades, floors |
| Slate | Metamorphic, layered | 3–4 | Low | Moderate | Roofing, garden paths, decor |
| Basalt | Volcanic | 6 | Very low | Resistant | Paths and yard paving, steps |
Note: «engineered quartz» (an agglomerate of quartz chips and resin) and marble-look porcelain tiles are not natural stone. They are good materials, but their price, care and warranty terms are different — ask for the exact material name in the listing.
Natural stone on Prayk: listing counts and prices
| Selection | Listings | With a price | Median | Middle half of listings |
|---|---|---|---|---|
| Building Materials, «mərmər» in title | 49 | 30 | 75 AZN | 23–98 AZN |
| Building Materials, «qranit» in title | 30 | 21 | 75 AZN | 20–85 AZN |
| Tiles and cladding materials, whole section | 269 | 238 | 15 AZN | 13–45 AZN |
Keep three points in mind when reading these figures. First, 19 marble listings have no price — sellers quote individually by size, thickness and finish, which is normal in the stone trade. Second, the 15 AZN median of the tiles and cladding materials section includes ceramic tiles and decorative panels, so it is not directly comparable with natural stone. Third, local limestone barely shows up in the catalogue: a search for «mişar» in building materials returned no stone listings, and many of the 55 listings matching «daş» (stone) are stone-wool insulation panels, concrete and mixes. If you are after «mişar daşı» or Absheron limestone cladding, check the building blocks, bricks and panels section and talk directly to sellers who work with quarries.
What drives the price per m²?
- Type and grade. Even within one type, the price can vary several times over depending on how rare the colour and pattern are and the country of origin.
- Format. Ready-cut tiles (for example 30×60 or 60×60 cm) usually cost less than a slab — a single large sheet. Slabs are for custom cuts such as worktops, steps and window sills.
- Thickness. 2 cm and 3 cm sheets differ in both price and weight; floors, stairs and outdoor areas need thicker stone.
- Surface finish. Polished (glossy), honed (matte), brushed (soft texture) and flamed (rough, non-slip) finishes cost different amounts and suit different places.
- Cutting and edging. Chamfers, rounded edges and cut-outs for a sink or hob are usually charged separately, per linear metre or per piece.
- Installation. Labour, adhesive and substrate preparation are not included in the stone price.
- Allowance. Add 10–15% to the area for cutting waste; complex rooms and diagonal layouts need more.
Worked example: for a 12 m² balcony floor, 12 × 1.1 = 13.2 m², so order about 13.5 m². Ask the seller for four separate lines: stone price per m², cutting and edging, installation, delivery. If you compare only the answer to «how much per m²?», you will be comparing different things.
Which stone for which job?
Facades
Outdoors, water absorption and frost resistance come first. Granite and basalt need almost no care; travertine and limestone look great but must be protected with a water-repellent impregnator, or white salt stains and darkening can appear. Facade cladding may need mechanical fixings (anchors) — leave the job to facade specialists.
Floors and stairs
In high-traffic areas (hallways, entrances, stairs), granite and quartzite resist scratches best; marble loses its shine over time. For steps and outdoor use, choose a honed or brushed finish rather than polished — wet polished stone is slippery.
Kitchen worktops
Among natural stones, granite stands out for resisting heat, knives and stains; marble dulls from lemon, tomato and wine. If you want a light stone, learn to tell quartzite from marble — that is what the acid test below is for.
Bathrooms and interior walls
Loads are low and looks matter here, so marble and travertine fit well. Seal the stone after installation and avoid acidic tile cleaners.
Yards, gardens and pool surrounds
Basalt, granite and brushed travertine reduce slipping. Slate's layers make it good for paths and decor, but they can flake in frost.
Memorials
For work that will stand outdoors for decades, granite outlasts marble — rain and air pollution slowly erode marble. Stone craftsmen are listed in the marble work section.
Checks before you buy: 7 steps
- Buy the whole quantity from one batch, in one go — a later batch may differ in colour.
- See the whole slab in the warehouse, not in a photo: the position of veins and spots affects the cutting plan.
- Water test: put a few drops on the surface. If the water soaks in within a couple of minutes and leaves a dark spot, the stone is porous and needs sealing.
- Acid test — only on a small offcut: lemon juice leaves a dull mark on marble and limestone but not on granite or quartzite. This helps catch marble sold as «granite» or «quartzite».
- Check cracks and fills: hold the slab to the light. Resin-filled pores (especially in travertine) are normal, but a crack should not run through the full thickness.
- Measure thickness at several points and look for chipped edges.
- Ask for the full material name, origin and finish in writing — especially where porcelain and engineered quartz are sold alongside.
If you do not know the name of a stone you like, a photo is enough: Prayk's image search finds similar listings. If the type you need is not listed yet, the search agent will tell you when it appears.
Care: how natural stone lasts for years
- Sealing. Treat porous stones (marble, travertine, limestone) with an impregnating sealer after installation and then periodically. How often depends on the manufacturer's instructions and how heavily the surface is used; the water test will show when protection has worn off.
- Gentle cleaning. Use pH-neutral cleaners. Vinegar, lemon, bleach and abrasive powders damage marble and limestone.
- Do not let stains sit. Wipe up wine, coffee and grease immediately — once they soak into the pores they are much harder to remove.
- Outdoor moisture. White salt stains on facades and fences come from moisture moving out of the wall; drainage and water-repellent treatment reduce them.
- Scratch protection. Put a mat at the entrance on marble floors and felt pads under furniture legs.
Frequently asked questions
Marble or granite — which is more durable?
Granite (6–7 on the Mohs scale) is much harder than marble (3–4), resists acid and absorbs little water, so it lasts longer in kitchens, on stairs, outdoors and in memorials. Marble is softer and acid-sensitive, but on interior walls, in bathrooms and on low-traffic floors it is beautiful and long-lasting.
How much does natural stone cost per m² in Baku?
As of 22 September 2026, the median of priced marble listings on Prayk is 75 AZN (half at 23–98 AZN), and granite listings also have a median of 75 AZN (half at 20–85 AZN). The price depends on type, thickness, surface finish and cutting, while installation and delivery are usually charged separately.
What is the difference between travertine and «mişar daşı» limestone?
Both belong to the limestone family. Travertine is a denser stone formed from hot-spring deposits, with characteristic pores, and is sold as polished or brushed tiles. Absheron's «mişar daşı» is a soft, light and very porous limestone, cut into blocks mainly for wall masonry and facades. Both need a water-repellent sealer.
Which natural stone suits a kitchen worktop?
Granite and quartzite — both are hard and resistant to heat and acid. Marble in a kitchen picks up dull marks from lemon, tomato and wine; if you choose it, you need to accept that «patina» and seal the surface regularly.
How do you care for natural stone?
Seal porous stones periodically, clean with pH-neutral products, avoid vinegar, lemon and abrasives, and wipe up spills and grease straight away. If a drop of water starts soaking in quickly, it is time to renew the sealer.
Sources and methodology
Listing counts and prices were taken from Prayk's public API on 22 September 2026: listings in the Building Materials section (with all subsections) with «mərmər», «qranit», «daş» and «mişar» in the title, plus the Tiles and cladding materials subsection as a whole. The median and «middle half» (25th–75th percentiles) use only listings priced in AZN; a price may be per m², per piece or for a service, so the figures are a guide. Hardness values are general geological data on the Mohs scale; ask the seller for the technical documents of a specific batch. More on choosing and caring for stone: Natural Stone Institute (the international natural stone industry association).